5 Accessories

When transporting the machine, make sure that the following parts are supplied.

TABLE 5 ACCESSORIES

DESCRIPTION Part No. (Qty.) Note

OWNERS MANUAL 420-6602-01(1)

Figures

If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

KEY MASTER 220-5576 (2)

For opening/closing the doors

For the CASHBOX DOOR

The Keys are inside the Coin Chute Door at the time of shipment from the factory.

GD-ROM SERVICE MANUAL ENG 420-6620-01 (1)

INSTRUCTION MANUAL FOR THE GAME BOARD AND GD-ROM

The Keys are inside the Coin Chute Door at the time of shipment from the factory.

SW MICRO TYPE 509-5080 (1)

Spare, see Section 10.

LAMP WEDGE 6V 3W 390-5160 (1)

Spare, see Section 13.

GLASS CLEANER 090-0174 (1)

Used for cleaning the Front Glass of the Projector. See Section 14.

c10>

TAMPERPROOFfWRENCH M4 540-0006-01 (1) TOOL

CARTON BOX 601-10532 (1) Used for transporting the Game Board. See FIG. 5 a.

CARTON BOX 601-10532 (1) Used for transporting the Game Board. See FIG. 5 a.

HOW TO USE THE CARTON BOX

IMPORTANT

When requesting for the replacement/repair of this product's Game Board (NAOMI BOARD), follow the instructions below. Transporting the Game Board in an undesignated status is unacceptable. An erroneous handling can cause parts damage.

• Put the Game Board in the Carton Box together with the Shield Case. Do not unnecessarily disassemble nor remove parts.

• By paying careful attention to the following Figure and the direction shown by on-Carton-Box printing, put the Shield Case in the Carton Box.

• When putting the Shield Case in the Carton Box, do not remove Leg Brackets.

• The projected portions of the packing material is intended for cushioning. Therefore, do not bend the projected portions.

• Do not remove the DIMM board without fail.

"CHECK SIDE" Display

"CHECK SIDE" Display

FIG. 5 a

Fold the packing material in the sequential order of the numbers shown in the Figure, enfold the Shield Case and put it in the Carton Box. Positioning the Shield Case upside down or packing in the manner different from what is shown in this Figure can cause the Game Board and other parts to be damaged.

The following Table 5b lists the parts that had been separately packed when the product was shipped from the factory but are necessary when you use the product. These parts will be mounted on the product when installing and assembling it.

TABLE 5 b

BILLBOARD PLATE

See 1 of Section 6.

PLATE HOLDER SPY-0005 (1) See 1 of Section 6.

BILLBOARD PLATE R SPY-0004 (1)

See 1 of Section 6.

TAPPING SCREW 011-T03512 (2) See 1 of Section 6.

GD DRIVE BRACKET 105-5435 (1)

To be mounted on the GD-ROM drive. see 3 of Section 6.

FLANGE NUT 050-F00500 (4) Used for securing the GD-ROM DRIVE. see 3 of Section 6.

GD-ROM 610-0625-0001 (1)

Game software media contained in a plastic case. see 3 of Section 6.

NOTE: A packing/shipping method of this product is specific with this CONFIDENTIAL MISSION DX TYPE product. It may be different from, therefore, the descriptions in the GD-ROM Service Manual.

TAPPING SCREW 012-P00408 (4) Used for securing the GD-ROM DRIVE. see 3 of Section 6.

TAPPING SCREW 012-P00408 (4) Used for securing the GD-ROM DRIVE. see 3 of Section 6.

AC Cable (Power Cord)

600-6729 (1) TAIWAN

600-6618 (1) OTHERS

600-6619 (1) HONG KONG

Used for installation, see 4 of Section 6.

WIRE HARN EARTH W/LUG M6

For TAIWAN.

Used for installation, see 4 of Section 6.

CORD CLAMP 280-5009-01 (1) Used for securing the power cord. see 4 of Section 6.

The following Table 5c lists the parts that are separately marketed but are necessary when booting this product's software. When having unpacked the shipping crate, make sure that all the parts in this Table 5C are in the crate. If not so, contact where you have obtained the product.

GD-ROM DRIVE 610-0617 (1)

Device that loads the software in a GD-ROM disk. see 3 of Section 6.

GD-ROM DRIVE CARTON BOX

Used for transporting the GD-ROM DRIVE. See FIG. 5 b.

This carton box is a standard accessory of the GD-ROM drive. If you want to obtain the carton box itself separately, specify the part number 601-11031.

HOW TO USE THE CARTON BOX (GD-ROM DRIVE)

IMPORTANT

When you want to order for replacing or repairing service of the GD-ROM drive that is used by the product, pack it in a carton box as instructed below, and then deliver the carton box to a service agent. If you do not observe the instruction, your order may not be accepted or may be charged additionally. If you handle the GD-ROM drive differently from the following instructions, its components may be damaged.

• Contain the GD-ROM drive in a dedicated carton box. Do not disassemble it or remove any part from it unless otherwise instructed.

• Before containing the GD-ROM drive in a dedicated carton box, attach the GD-ROM drive lid (DISC LID) onto the drive and fix the lid with a screw.

• Before containing the GD-ROM drive in a dedicated carton box, remove the GD-ROM disk from the drive. Do not attempt to move the GD-ROM drive with a GD-ROM disk inside.

• Before containing the GD-ROM drive in a dedicated carton box, remove the GD-ROM drive bracket. Carefully keep the GD-ROM drive bracket and the 4 set screws, because they will be reused.

• When inserting the GD-ROM drive into a dedicated carton box, be careful about an inserting direction as illustrated below.

• The packing materials in a carton box are used as a cushion. Use them always when inserting the GD-ROM drive into a dedicated carton box. Do not bend them.

0 0

Post a comment