6 Assembling And Installation

Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard. Perform assembling as per this manual. Since this is a complex machine, erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance.

When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage.

Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard.

Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards.

This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult.

To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

CAUTION!

0 When handling plastic parts, use care. Do not give a shock or apply excessive load to the fluorescent lamps and plastic parts. Failure to observe this can cause parts damage, resulting in injury due to fragments, cracks and broken pieces.

£ To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.

When carrying out the assembly work, follow the procedure in the following 6-item sequence:

[T] INSTALLATION OF BILLBOARD PLATE AND BILLBOARD PLATE R SECURING IN PLACE (ADJUSTER ADJUSTMENT) INSTALLING THE GD-ROM DRIVE (SETTING A GD-ROM DISK) [4] POWER SUPPLY, AND EARTH CONNECTION TURNING POWER ON ASSEMBLING CHECK

The master key (accessories) in addition to the tools such as a Phillips type screwdriver, Box nut screwdriver and wrench are required for the assembly work.

Phillips type screwdriver (for M3,M4 screw)

Phillips type screwdriver (for M3,M4 screw)

WRENCH (for M16 hexagon bolt)

WRENCH (for M16 hexagon bolt)

Box nut screwdriver

7mm (For M4 hexagon nut)

Box nut screwdriver

7mm (For M4 hexagon nut)

KEY MASTER

KEY MASTER

INSTALLATION OF BILLBOARD PLATE AND BILLBOARD PLATE R

^^ Remove the 4 truss head screws, and thereby remove the lamp cover B. (2 Insert the billboard plate, and tighten the 4 truss head screws to fix the lamp cover B.

FIG. 6. 1 a

When performing work, prepare a step.

Insert the billboard plate R into a slot on the rear of the billboard case. ^^ Using a both-side adhesive tape, stick the plate holder onto the rear of the billboard plate R. Tighten the 2 tapping screws, and thereby fix the plate holder.

FIG 6. 1 b

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

WARNING!

Make sure that all of the adjusters are in contact with the floor. If they are not, the cabinet can move and cause an accident.

This machine has 4 casters and 4 adjusters. When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

Move the machine to the installation position.

Cause all of the adjusters to make contact with the floor. By using a wrench, make adjustments in the height of the adjusters to ensure that the machine's position is level.

^^ After making adjustments, fasten the adjuster nut upward and secure the height of the adjuster.

Approx.5mm

FIG. 6. 2 b ADJUSTER

Refer to this Fig. (Scale:1/100) for the layout of the place of installation.

Provide sufficient space so as to allow for ventilation by the ventilation fan.

INSTALLING THE GD-ROM DRIVE (SETTING A GD-ROM DISK)

IMPORTANT

Carefully handle the GD-ROM drive so as not to contaminate the disk and the readout lens with stains and dust particles.

Do not continue to use the scratched GD-ROM disk. The scratched GD-ROM disk may cause the system to malfunction.

Set the GD-ROM disk onto the GD-ROM drive with its labeled side facing upward.

Unpack the shipping crate, and take out the GD-ROM drive, GD-ROM drive bracket, and GD-ROM disk.

GD DRIVE BRACKET GD-ROM DRIVE

^^ Use the 4 tapping screws to fix the GD-ROM drive bracket onto the GD-ROM drive. Be careful about a fixing direction.

App<iofitlon diagram

CAUTION for U. S. A., Europe, and Australia: Attach the 2 caution stickers for a laser ray onto the GD-ROM drive.

PHOTO 6. 3 b

@ Set the GD-ROM disk onto the GD-ROM drive with its labeled side facing upward.

Return the lid to its original place, and fix it with 1 truss head screw. Be careful not to fasten the screw too tightly.

.TRUSS SCREW (1) M3 X 8

^^ Unlock the front-left door, and thereby remove the door from the cabinet.

PHOTO 6. 3 d

© Now you will take out the ASSY MAIN BD froi the cabinet and mount the GD-ROM drive onto i First, remove the 7 connectors from the upper section of the rear of the door.

Disconnect the connector.

D-SUB connector

Disconnect the connector.

PHOTO 6. 3 e

^^ Remove the D-SUB connector from the filter board (a part of the NAOMI board on the ASSY MAIN BD). Unclamp the cable with the D-SUB connector.

D-SUB connector

(9 Remove the 2 wing bolts that fix the ASSY MAIN BD's base (a wooden plate).

(£0 Take out the ASSY MAIN BD from the cabinet. In this instance, be careful not to catch the wires on or in the parts.

13 Insert both the GD cable connector (for data communication) and the power cord connector (JST NH6P) into the GD-ROM drive. Be careful about an inserting direction in this instance. Make sure that the connectors are inserted firmly and completely.

PHOTO 6. 3 j

©Return the ASSY MAIN BD (now installed with the GD-ROM drive) into the cabinet. Tighten the 2 wing bolts, and thereby fix the base.

PHOTO 6. 3 k

©Following the above-described actions in a reverse order, connect the connectors, clamp the wires/cables, and install the front-left door.

POWER SUPPLY, AND EARTH CONNECTION

WARNING!

Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

The AC Unit is mounted on the rear of the machine. The AC Unit has Circuit Protector, Main SW, Earth Terminal and the Inlet which connects the Power Cord.

Ensure that the Main SW is OFF.

EARTH TERMINAL ■ Connect with the , indoor earth terminal.

EARTH TERMINAL ■ Connect with the , indoor earth terminal.

FIG. 6. 4 a AC unit

^^ Connect one end of the earth wire to the AC Unit earth terminal, and the other end to the indoor earth terminal. The AC Unit earth terminal has a Bolt and Nut combination. Take off the Nut, pass the earth wire through the Bolt, and fasten the Nut. Note that the Earth Wire is incorporated in the Power Cord for the Areas of AC 120 V (USA) and AC 220 ~ 240V, and therefore, this procedure is not necessary.

Connect the Earth Wire to the Earth Terminal.

Connect the Earth Wire to the Earth Terminal.

FIG. 6. 4 b Earth Wire Connection

(Q Firmly insert the power plug into the socket outlet. Insert the opposite side of Power Cord plug to the AC Unit's connector ("INLET").

FIG. 6. 4 c Connecting Power Cord and Earth Wire

TURNING POWER ON

Turn on the AC unit's main switch to connect the power. When the power is connected, the fluorescent light in the billboard becomes on. A few seconds later a system startup screen appears and then an advertising screen (plying for a player screen) appears. Time until displaying an advertising screen is not constant; it varies from some tens of second up to several minutes. This is due to the functional characteristics of the GD-ROM system's rechargeable battery and therefore normal.

When an advertising screen appears, sound is output from the speakers on the right and left of the PTV cabinet. Sound is not output if you have set the function to off. After the power is disconnected, the system can maintain the data of credit number and ranking. The system cannot maintain, however, the fractional number of coins (not enough for one credit) and the bonus adder count data.

On-screen images are outputted.

Fluorescent lamp (in the Billboard) is lit.

Sound is emitted.

On-screen images are outputted.

Fluorescent lamp (in the Billboard) is lit.

Sound is emitted.

ASSEMBLING CHECK

In the TEST MODE, ensure that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 9).

In the test mode, perform the following test:

(1) MEMORY TEST

Selecting the RAM TEST and DIMM BOARD TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

RAM TEST

IC29

GOOD

IC35

GOOD

IC09

GOOD

IC10

GOOD

IC11

GOOD

IC12

GOOD

IC16

GOOD

IC18

GOOD

IC20

GOOD

IC22

GOOD

IC17

GOOD

IC19

GOOD

IC21

GOOD

IC23

GOOD

PRESS TEST BUTTON TO EXIT

DIMM BOARD TEST

DIMM BOARD TEST

PROGRAM VER : 1.02 DIMM SLOT 0 : GOOD DIMM SLOT 1 : GOOD DIMM STATUS : GOOD

CHECKING DIMM BD DIMM0 - GOOD DIMM1 - GOOD IC34,35S - GOOD IC10,11S - GOOD GD DRIVE - GOOD --- COMPLETE ---

PRESS TEST BUTTON TO EXIT

(2) C.R.T. TEST

C.R.T. TEST PAGE 1/2

RED

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the moniter is tested) to be displayed. Although the moniter adjustments have been made at the time of shipment from the factory, make judgment as to whether an adjustment is needed by watching the test mode screen. If it is necessary, adjust the moniter by referring to Section 11.

C.R.T.

TEST

PAGE 2/2

PRESS TEST BUTTON TO EXIT

(3) INPUT TEST

INPUT TEST

PLAYER 1

PLAYER 2

TRIGGER

OFF

OFF

SCREEN-IN

OUT

OUT

GUN-X

0

0

GUN-Y

0

0

START

OFF

OFF

PRESS TEST AND SERVICE BUTTON

TO EXIT

Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

(4) OUTPUT TEST

Select OUTPUT TEST from the menu in the test mode to cause the screen (on which each lamp and wiring connections are tested) to appear. Ensure that lamp light up satisfactorily.

OUTPUT TEST

PLAYER 1 PLAYER 2 > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(5) GUN ADJUSTMENT

Before starting the operation, play the game by yourself and make sure that the gun readjustment is not needed and that you can play the game without a problem. Although completed at the factory, the gun adjustment may be necessary because after the adjustment the product has been disassembled for packing and shipping. For more information about the gun adjustment, see Section 9-3E.

GUN ADJUSTMENT

PLAYER1

LEFT aa bb

TOP aa bb T

BOTTOM aa bb BO

CENTER X aa bb CEN

Y aa bb

DEFAULT DEF

CHECK CHECK

PLAYER2 OLD : NOW

HT aa bb LEFT aa OP aa TTOM aa TER X aa Y aa

AULT

bb bb bb bb bb

Was this article helpful?

0 0

Post a comment