Sw

NC means no connection required for Cyberball 2072. TP means twisted pair. 1. Connect four of the large BN wires to the 5V RTN (GND) terminal on the power supply unless he power supply has a 12V RTN. If there is a 12V RTN, connect one of the wires to the 12V RTN (GND) terminal. Three of the R wires so to the +5V terminal on the power supply. If the power supply has a +SENSE terminal, connect one of these three wires to the +SENSE instead of the +5V. The fourth wire goes to the red wires on the...

5

Use this wire if you want an external self- er, the Cyberball 2072 kit already has one self-test switch on the JSA Audio PCB. If you connect an external self-test switch, first make sure the switch 011 the PCB is switched off Then connect this wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the self-test switch to one of the BK W wires (GND), 8. Connect to the N.O. tennlnals of the two coin switches. Connect the common terminals of the coin switches to...

Maintenance and Troubleshooting

This chapter contains regular maintenance information, troubleshooting tables, and repair procedures for your The chapter has two parts. The first part contains three troubleshooting tahles. One table has general troubleshooting information, the second contains the voltage levels and test points on the PCBs, and the last is a table of ROM-caused problems with specific ROMs to check and replace. The last part of the chapter has information about connecting the video display to the Cyberball 2072...

Info

II4 M IV P h' HIMNAL California Crush Tokyo Flash New York Thunder Moscow Machine Berlin Invasion London Lightning Use the information shown on the two statistics screens and on the histogram screen to keep track of your game use. Record the information on the Cyber-ball 2072 statistics page in the back of this manual. The information shown on the two statistics screens (shown in Figures 2-6 and 2-7) is accumulated from the last time the statistics were reset. At the bottom of the first...

Note

Not all of the options are shown when you enter this screen. The word More shows at the bottom of the screen to indicate more options. Use the left joystick to scroll through the options. V , III M'7 The game options are explained below. The settings, willi defaults, aie shown in Tabic 2-4. Clear High Score Table clears the high score table, if it is set to yes. Restore Factory Options allows you to set all the game options to the factory options by choosing yes. If you want to use your own...

Hbt

M Beginner Games is the number of games played in begiiuiei mode. Comp Coach Games is the number of games played under the beat-the-coach format. Game Breakers is the number of games played under this unique format. 1 Period Games is the number of games in which the playerCs played for only one period of the complete six-period Cyberball 2072 game. 2 3 4 5 6 Period Games show the number of games in which the playerCe played for two to si periods. 7-Plus Period Games shows the number of games in...

Caution

Do not unplug or plug in the Cyberball 2072 game printed-circuit board PCB edge connector while the power is on. You could seriously damage the PCB. m Drill with 1 4 inch drill bit, a 1 3 16-inch hole cutter or 1 3 16-inrh rhassis punch , and a 1 V4-inch hole cutter Fast-ons if you are installing a new JAMMA harness Preparing the Existing Game for Conversion 2. Remove the old game PCB s . Remove the game harness if it is not Japan Amusement Machinery Manufacturers Association QAMMA -compatible....

Installation

This manual provides information for installing, testing, and troubleshooting the Cyberbalt 2072 Universal kit. The manual is divided into the following chapters Chapter 1 describes the installation procedure and the Cyberball 2072 game play. Chapter 2 contains self-test procedures. Chapter 3 contains troubleshooting procedures. Chapter 4 contains illustrated parts lists. Chapter 5 contains the schematics for the game PCB and JSAII Audio PCB. Also bound into Chapter 1 of this manual is the...