• All returned merchandise must have a Return Merchandise Authorization (RAM) number marked clearly on the outside of the package.
• You must obtain all RAM numbers from your authorized Incredible Technologies, Inc. distributor. Please have your Incredible Technologies, Inc. serial number available when calling for an RMA number.
• Merchandise returned without an RMA number will not be accepted.
• Advance replacement boards will be shipped to distributors or, at the distributor's request, will be shipped directly to the operator.
• Advance replacement boards will be billed to the distributor until Incredible Technologies, Inc. receives the returned board, at which time a credit will be issued.
• All repairs and/or replacements will be shipped within 24 hours of receipt or request (subject to availability).
This equipment complies with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
02/97
1 getting started 2
SAME PACKAGE CONTENTS 2
RECOMMENDED TOOLS AND SUPPLIES 2
2 INSTALLATION PREPARATION 2
THE CABINET 2
Power Requirements 2
Monitor Requirements 3
Cabinet Selection 3
Preparing a used cabinet for golden tee '97 3
THE CONTROL PANEL 3
Trackball Preparation — 4
Button Preparation 6
THE GRAPHICS OVERLAY 6
Control Panel Overlay Installation 6
Function Labels Overlay Installation 6
Marquee Installation 6
WIRING AND HARDWARE ASSEMBLY 7
Control Panel Assembly 7
Printed Circuit Board (PCB) 7
Wire Harness 7
Power Wires 8
Monitor Wires 8
Speaker Wires 8
SYNC 8
Coin Doors, Test Switch, Service Button, and Volume Control Panel 9
Mars Light Hookup 9
Final Check 9
3 INITIAL START-UP 10
4 DIP SWITCH SETTINGS 10
5 OPERATOR MODE 11
VOLUME SETTINGS 12
OPERATOR ADJUSTABLES 12
Game Mode Selection 13
Game Resets 13
Attract Mode Sounds 13
Credits and Coin Door Settings 14
Delay Time Adjustment 14
Skill Level Adjustment 15
Hole In One Contest Mode 15
Coin Door Protection Menu 16
GAME AUDITS 16
Display Coin Audits 16
Display Game Selection Audits 17
Number of Golfers and Holes Played 17
Pine Creek Audits 17
Cora\ Ridge Audits 17
Red Sands Audits 18
Display Hardware Audits 18
Reset Audits 18
LEADER BOARD MENU 18
Display Leader Board Menu 19
Clear Leader Board Menu 19
SYSTEM TESTS 19
Video Screen Tests 20
Full GROM Checksum Test 20
Fast GROM Checksum Test 21
Video Ram Test 21
Palette RAM Test 21
Board Tests 22
Sound Tests 22
Control Panel Test 22
Voltage Adjust Test 22
appendix a
GENERAL TROUBLESHOOTING 24
VIDEO PROBLEMS 25
SOUND PROBLEMS 26
CONTROL PROBLEMS 27
POWER-UP PROBLEMS 28
MISCELLANEOUS PROBLEMS 29
appendix b
JAMMA HARNESS CONNECTION 30
JAMMA HARNESS CONNECTION 31
TRACKBALL CABLE CONNECTION 31
appendix C
I/O and JAMMA SCHEMATIC 32
appendix d
WARRANTY INFORMATION 34
GETTING STARTED
IIIS!
(1) Printed Circuit Board (PCB) Assembly
(1) Connecting Wire Harness (JAMMA)
(1) Trackball Assembly w/Metal Plate
(1) Trackball Cable Assembly
(3) Button Assemblies
(1) Marquee Styrene
(1) Marquee Plexiglas
(1) Control Panel Overlay
(1) Set of Function Labels
(1) Manual
Phillips and Slotted Screwdrivers Socket Set
Wire Cutters and Strippers
Pliers or Channel Locks
Electric Drill with 3/32", J", and 7/16" Bits
Chassis or Sheet Metal Punch
Small File
Razor Knife and Sharp Blades
Straight Edge
Staple Sur and Staples
Soldering Iron and 60/40 Resin Core Solder
Vacuum Cleaner
Assorted Fastening Hardware
Heat Shrink Tubing (3/32", 1/8", and 3/16")
Masking Tape or 4" Wire Ties if you do youft own painting, you'll need these paint supplies:
• Air Brush or Paint Sprayer
• Paint Roller and Pan
INSTALLATION PREPARATION
BEFORE YOU START
1. Check to see if all the needed parts have been included in your kit (See GAME PACKAGE CONTENTS .)
2. Do you have the necessary tools? (See RECOMMENDED TOOLS AND SUPPLIES.)
3. Do not work with any part of the system plugged in (lights, monitor, or power supply).
Power Requirements_
Make sure the game you have chosen to convert is able to supply all the required voltages for GOLDEN TEE '97.
5 amps 2 amps warning!!!
The output level of many "regulated" switching power supplies actually vary with load. For this reason, the power supply from an old game may not be correctly adjusted for SÖLDEN TEE '97. This makes the existing power supply inappropriate and hazardous to your new game. Therefore, it is very important to adjust the +5 VDC supply WITHOUT connecting the PCB, then readjusting it later, after the PCB has been installed. Measure power on the PCB, on an I.e.. Damage will occur if the power supply is outside the acceptable limits (between 4.8 and 5.5 VDC.)
Was this article helpful?
Post a comment