4 Assembling And Installation

• Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard.

• Perform assembling as per this manual. Since this is a complex machine, erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance.

• When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage.

• Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard.

• Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a fire risk.

• Do not carelessly push the PTV. Pushing the PTV carelessly can cause the PTV to fall down.

• This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation.

• Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult.

• To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

• When handling plastic parts, use care. Do not give a shock or apply excessive load to the fluorescent lamps and plastic parts. Failure to observe this can cause parts damage, resulting in injury due to fragments, cracks and broken pieces.

• To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.

• Make sure that the GD cable connector is inserted parallel to the plug. Improper insertion may cause damage to the connector and present a fire risk.

When carrying out the assembling and installation, follow the following 8-item sequence.

INSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC) POWER SUPPLY, AND EARTH CONNECTION TURNING POWER ON

The master key (accessories) in addition to the tools such as a Phillips type screwdriver, wrench, socket wrench and Ratchet Handle are required for the assembly work.

Phillips type screwdriver

Phillips type screwdriver

WRENCH (for hexagon bolt)

TAMPERPROOF WRENCH

T-40 Torx 5/16-18 (1) T-27 Torx 1/4-20 (1) T-15 Torx 8/32 (1) T-10 Torx (1) Tool (Included with Unit)

WRENCH (for hexagon bolt)

INSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)

• Carefully handle the GD-ROM drive so as not to contaminate the disc and the readout lens with stains and dust particles.

• Do not continue to use the scratched GD-ROM disc. The scratched GD-ROM disc may cause the system to malfunction.

• Set the GD-ROM disc onto the GD-ROM drive with its labeled side facing upward.

• The key chip is a precision device. Handle it carefully and avoid exposure to heat, shock and static electricity, as these may cause damage to the device.

• The key chip is contained in the GD-ROM disc case. Always use them as a set.

This section explains how to remove the ASSY MAIN BD from the PTV cabinet, set the GD-ROM disk onto the GD-ROM drive, and install the GD-ROM drive onto the ASSY MAIN BD.

(l^ Unpack the shipping crate, and take out the GD-ROM drive, GD-ROM drive bracket, and GD-ROM disc.

GD DRIVE BRACKET

GD-ROM DRIVE

GD DRIVE BRACKET

GD-ROM DRIVE

Use the 4 tapping screws to fix the GD-ROM drive bracket onto the GD-ROM drive. Be careful about a fixing direction.

TAPPING SCREW (4)

TAPPING SCREW (4)

Application diagram

H SSmi CAL I

CLASS 3A LASEH PRODUCT. ■

H SSmi CAL I

CLASS 3A LASEH PRODUCT. ■

Please follow the drawing and place the sticker with the right language.

CAUTION for U. S. A., Europe, and Australia: Attach the 2 caution stickers for a laser ray onto the GD-ROM drive.

(3j Remove the 1 truss head screw that fixes the GD-ROM drive lid (DISC LID). And turn clockwise the lid to remove.

(3j Remove the 1 truss head screw that fixes the GD-ROM drive lid (DISC LID). And turn clockwise the lid to remove.

PHOTO 6. 5 b

(4) Set the GD-ROM disc onto the GD-ROM drive with its labeled side facing upward.

(5) Return the lid to its original place, and fix it with 1 truss head screw. Be careful not to fasten the screw too tightly.

M3x8

Place the ASSY MAIN BD on a flat vertical surface.

Using the 4 screws, fix the GD-ROM drive onto the ASSY MAIN BD.

M4*16, w/flat & spring washers

Place the ASSY MAIN BD on a flat vertical surface.

Using the 4 screws, fix the GD-ROM drive onto the ASSY MAIN BD.

M4*16, w/flat & spring washers

Insert both the GD cable connector (for data communication) and the power cord connector (JST NH6P) into the GD-ROM drive. Be careful about an inserting direction in this instance. Make sure that the connectors are inserted firmly and completely.

Power Cord connector

GD Cable connector

Power Cord connector

GD Cable connector

Insert the Key Chip straight into the hole in the top of the Media Board on the upper part of the Game Board. Carefully check the direction the Key Chip is facing, and push it in as far as it will go.

KEY CHIP

KEY CHIP

PHOTO 6. 5 k

Attach the accessory stickers to both the Game Board and the Media Board.

KEY CHIP

KEY CHIP

MEDIA BOARD

MEDIA BOARD

POWER SUPPLY, AND EARTH CONNECTION

Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs.

Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shoc accident.

The AC Unit is located on one side of Cabinet. The AC Unit has Main SW, Earth Terminal and the Inlet which connects the Power Cord.

TURNING POWER ON

Turn on the AC unit's main switch to connect the power. When the power is connected, the fluorescent light in the billboard becomes on. A few seconds later a system startup screen appears and then an advertising screen (plying for a player screen) appears.

Time until displaying an advertising screen is not constant; it varies from some tens of second up to several minutes. This is due to the functional characteristics of the GD-ROM system's rechargeable battery and therefore normal.

When an advertising screen appears, sound is output from the speakers on the right and left of the PTV cabinet. Sound is not output if you have set the function to off.

After the power is disconnected, the system can maintain the data of credit number and ranking. The system cannot maintain, however, the fractional number of coins (not enough for one credit) and the bonus adder count data.

*NOTE: Picture may differ from actual unit. FIG. 6. 7

THE INTERFERENCE PREVENTION WIRING

WARNING!

When the game machines of a same or similar type are installed side by side, their sensors may interfere with each other. To reject the interference, follow the procedure below. The following game machines employ a same or similar type of sensor. If interference happens to the sensors, operation of the games may be mutually disturbed.

• THE HOUSE OF THE DEAD 2, U/R type, DX type and Super DX type

• THE LOST WORLD, U/R type, DX type and Super DX type

• BRAVE FIRE FIGHTERS

• CONFIDENTIAL MISSION, U/R type and DX type

• SHAKATTO TAMBOURINE

^ Locate an interference rejection wire inside the cabinet.

If the game machines of a same or similar type are installed side by side, place them alternately (place the machine with an interference rejection wire next to the machine without).

INTERFERENCE PREVENTION WIRING

INTERFERENCE PREVENTION WIRING

PHOTO 6. 8

• In order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.

• Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a fire risk.

• Do not expose the IC BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.

• Work should be performed by the Location's Maintenance Man or technical personnel. Performing work by those who do not have technical knowledge and expertise can cause electric shock accident or malfunctioning.

0 0

Post a comment