Player Panel Template 1610830

[ ] 1. If you're assembling both kit 15909 and optional player panel 45494, skip to Step 19. If you're assembling just kit 15909, proceed with the next step.

[ ] 2. Locate and unfold the player panel template. Temporarily stack newspapers, books, magazines, etc., on the template. The weight will flatten the template sufficiently for use.

[ ] 3. If necessary, remove buttons, joysticks and T-nuts from the old player panel and cabinet front. Remove the panel covering and artwork from the previous game. Remove and save hinges or mounting brackets.

[ ] 4. If necessary, fill the old player panel holes with wood, putty, glue, etc. Allow adequate time for materials to dry. Sand or file the player panel to a flat surface on both sides.

31-3479-1

HOUSING DECAL

LEFT SIDE

SLIT LOCATION

31-3480.1

CONTROL PANEL WALLPAPER

SLIT LOCATION

31-3479-1

HOUSING DECAL

LEFT SIDE

31-3480.1

CONTROL PANEL WALLPAPER

31-3479-1

HOUSING DECAL RIGHT SIDE

31-3479-3

HOUSING DECAL FRONT SIDE

31-3479-1

HOUSING DECAL RIGHT SIDE

31-3479-3

HOUSING DECAL FRONT SIDE

[ ] 6. Lightly moisten the cabinet with soapy water. Remove the backing from the wallpaper decal. Apply the decal to the player panel. Start at the top and work down. After you've positioned the decal, smooth it outwards. Take care to squeeze out air bubbles. If you can't remove a bubble, pop it with a knife or pin. Then smooth the bubble down. Allow the decal adhesive to set.

[ ] 7. Use a sharp knife to trim edges and cut holes for player panel buttons. Position control decals next to the appropriate hole locations. Allow the decal adhesive to set.

[ ] 8. Install the NBA hologram decal on the player panel.

[ ] 9. Install the plastic cover over the decals and panel. Attach the cover and deburr the edges. Group player controls by color (orange, red, blue and white). Joysticks are black. You must disassemble controls for panel mounting.

[ ] 10. Separate the switch from the orange PLAYER 1 START (left START) button. Bend the large prong away from the switch just enough to slide the switch off the housing. Unscrew the nut from the housing. Insert the button housing through its hole from the player panel's front. Screw the nut finger-tight onto the switch housing from the panel back. Rotate the housing so that switch terminals face the panel center. Tighten nuts firmly. Snap the switch back onto the housing.

[ ] 11. Repeat the previous step with the other three start buttons.

[ ] 12. Consult this chapter's illustration Player Panel Buttons. Install the other buttons.

[ ] 13. Tighten the pushbutton nuts firmly. Replace player panel components and hardware that you removed earlier.

[ ] 14. Measure the thickness of the player panel. If it is less than % inch (13 mm), use wooden spacers to recess the joysticks below the surface. Thicker player panels don't require wooden spacers.

[ ] 15. Install a carriage bolt in each small hole near each joystick opening. If the player panel is thin, place wood spacers over the carriage bolts. The spacers correct joystick-mounting depth.

[ ] 16. Invert one joystick. Remove the "E"-ring from the shaft. Remove the handle and plastic ring (large washer) from the joystick base. The bushings must remain in the base. The top of the joystick base fits against the bottom of the player panel (or spacer, if used). Orient the connector toward the START buttons. Align mounting holes. Attach the base to the player panel bottom. Slide the plastic ring around the shaft so that the rough side is beside the knob handle. Slide the shaft through the player panel and base. Replace the "E"-ring. Repeat this step for the remaining joysticks.

[ ] 17. Locate the I-40 Joystick Interface Board. Insert a plastic spacer into the bottom of a mounting hole. Press the spacer to seat it fully. Repeat this procedure until all spacers attach to the board.

[ ] 18. Place the I-40 Interface Board inside the player panel housing. See the housing drawing. Position the I-40 Board near the housing's right side. Assure that controls don't hit components when you open and close the panel. Leave space above and beside board connectors for mating connectors. Mount the I-40 Board with a screw through each plastic spacer.

[ ] 19. The completed player panel should now resemble the illustration below. Install the modified panel housing onto the cabinet with the original mounting hardware. Firmly tighten fasteners.

[ ] 20. Install the side and front player panel decals onto the player panel housing.

A-21939-1

49 WAY JOYSTICK

20-10209-1

PUSH BUTTON RED

20-10209-2

PUSH BUTTON

WHITE

20-10209-3

PUSH BUTTON BLUE

20-10209-7

-PUSH BUTTON ORANGE

20-10209-7

-PUSH BUTTON ORANGE

20-10209-1

PUSH BUTTON RED

20-10209-2

PUSH BUTTON

WHITE

20-10209-3

PUSH BUTTON BLUE

TYPICAL MODIFIED PLAYER PANEL

CONTROL PANEL ASSEMBLY

PLAYER 3

CONTROL PANEL HARNESS

04-11089

1-40 BOARD ASSEMBLY

- PLAYER 4

- PLAYER 4

CONTROL PANEL ASSEMBLY

PLAYER 3

CONTROL PANEL HARNESS

04-11089

1-40 BOARD ASSEMBLY

PLAYER 2

Control Panel Harness

PLAYER 2

- PLAYER 1 GROUND STRAP FROM CABINET

TYPICAL PLAYER PANEL HOUSING

Xybots Cabinet Control Panel

TYPICAL COMPLETED CABINET

0 0

Post a comment