622 Diagonal Switching interlace modenoninterlace mode

Interlace mode: The mode where precise expression, curves and smooth lines shall be displayed compared to "non-interlace mode".

The vertical resolution is doubled without changing the horizontal/vertical frequency by shifting the display position of the screen to the vertical direction by half of one line once out of twice in display.

* Namco-made CYBERLEAD cabinet corresponds to the interlace mode setting.

Non-interlace mode: The mode to be used when slanted lines are irregular, or the whole screen flickers in "Interlace mode". This mode keeps the screen pictures uniform every time without shifting the display position of the screen.

D Perform the procedures D and 0 of "6-2-1 Common Operation" (p.25) to display the "Color edit" screen over the "Diagonal" screen.

* If "DISPLAY TEST" screen appears already, common operation Q is not needed.

/ EXIT COLOR EDIT ' NEXT COLOR TEST / EXIT

^sss'ssss

/ /

/ /

\

Interlace

/

Contrast

: OO

Bright

: OO

/

SubContR

:00

SubContG

:(X)

/

SubCont B

: OO

/

Interlace mode

How to initialize the value How to finish the color edit How to go to the next test pattern How to return to the test menu screen

/ EXIT COLOR EDIT ' NEXT COLOR TEST / EXIT

^sss'ssss

P2-START P2-BUTTON1 P1-BUTTON1 P1-START //Sffff/

P2-START P2-BUTTON1 P1-BUTTON1 P1-START //Sffff/

Interlace mode

How to initialize the value How to finish the color edit How to go to the next test pattern How to return to the test menu screen

If the "DIAGONAL" screen is not displayed, keep pressing the PI button switch until it is displayed.

* Each time you press the PI button switch, it shifts from "DIAGONAL" ->

"COLOR BAR" -> "CONVERGENCE" -> "DIAGONAL" , and its screen is displayed each time.

If the "Color Edit" screen is not displayed, press the P2 button switch. The "Color Edit" screen is displayed over the "DIAGONAL" screen.

* Press the P2 button switch to switch the "Color Edit" screen displayed / non-displayed.

PI button switch

P2 button switch

PI button switch

El Make sure that "Interlace" is selected at the right top of the screen.

* If it is "Non Interlace", change the setting to "Interlace" by following the steps below.

© Hit the PI 4-direction joystick to up or down to select "Non Interlace" at the right top of the screen. The arrow on the left of "Non Interlace" shows that it is selected.

© Hit the PI 4-direction joystick to right or left to change the setting from "Non Interlace" to "Interlace".

B Hit the PI 4-direction joystick to right at the same time to check that slanted lines are not irregular in every color, or the whole screen does not flicker.

* Each time you Hit the P2 4-direction joystick to right, the color of the slanted lines pattern changes from white -> blue -> red -> purple -> green -> light blue -> yellow -> black -> white in this order.

* In the Interlace mode, precise picture can be displayed compared to the Non Interlace mode. Due to the nature of the Interlace mode, however, some types of monitor cannot display the right picture, where slanted lines may be irregular or the whole screen may flicker.

Q When slanted lines are irregular or the whole screen flickers, switch "Interlace" to "Non

Interlace" at the top right of the screen following the steps below.

(!) Hit the PI 4-direction joystick to up or down to select "Interlace" at the right top of the screen. The arrow on the left of "Interlace" shows that it is selected.

(D Hit the PI 4-direction joystick to right or left to change the setting from "Interlace" to "Non Interlace".

Ei Press the PI start switch to return to the test menu screen after completing the whole "DISPLAY TEST".

Press the PI button switch 1 to display the adjusting screen for the other adjustment in the "DISPLAY TEST".

□ Perform "6-1-3 Finishing the Test Mode" (p.24) to exit the test mode.

PI button switch

PI start switch

PI 4-dire joystick

PI button switch

PI start switch

PI 4-dire joystick

Was this article helpful?

0 0

Post a comment