Removing the Tube and Speaker Board:
1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector (see Figure 3-11).
2. From the front of the game, remove the three button-head screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws ana washers that secure the iower attraction-panel retainer to the cabinet.
3. Remove the attraction glass.
5. Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.
Replacing the Fluorescent Tube:
1. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
2. Remove the cardboard locking tab at each end of the tube (see Figure 3-12). Slightly rotate the tube up or down and carefully remove it from the tube holder.
3. Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.
Replacing the Upper Speaker:
4. Disconnect the two plug-in connectors on the speaker. Note that the white wire ( + ) connects on the side marked with a painted dot.
5. Remove the screws that attach the speaker to the board (see Figure 3-12). Replace with a new speaker and reinstall the tube and speaker board.
Replacing the Lower Speaker:
From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in
Figure 3-11 Fluorescent Tube and Speaker Board Removal
Upright Cabinet
Figure 3-11 Fluorescent Tube and Speaker Board Removal
Upright Cabinet
148001-013
(Speaker)
70-304
179035-001
(Tube holder)
A037457-01
(Harness)
148001-013
(Speaker)
70-304
179035-001
(Tube holder)
A037457-01
(Harness)
142028-001
(Transformer)
142028-002 J
(Transformer)
79-561816P
(Wire nut)
A¡A A037540-01
(Ground wire)
Figure 3-12 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A Ireland-Built Upright Cabinet A039415-02 A Parts List
142028-001
(Transformer)
142028-002 J
(Transformer)
99-11003
(Starter)
99-11009
(Socket)
NOTE
To make sure that the fluorescent tube starts, check that the ground wire is firmly attached to both the ballast transformer and the steel tube bracket.
79-561816P
(Wire nut)
A¡A A037540-01
(Ground wire)
039366-01
(Board)
Figure 3-12 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A Ireland-Built Upright Cabinet A039415-02 A Parts List
Part No.
Description
142028-001
142028-002
A037457-01 A037540-01 70-304
78-6900402
79-561816P 99-11003 99-11006 99-11009
003053-01 037469-01 039418-01 003053-01 039144-01
148001-013 176015-112 179035-001 179125-001
For U.S-Built Upright Cabinet
60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly)
For Ireland-Built Upright Cabinet
50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly)
For U.S- and Ireland-Built Upright Cabinet
Tube and Speaker Harness Assembly
Ground Wire with Ring Lug
18-Inch, 15 W, Cool White Fluorescent Tube
Vinyl Foam Single-Coated Adhesive Tape, 1A-lnch Wide x Xrlnch Thick
Spring-Connector Wire Nut for 16- to 18-Gauge Wires Fluorescent Tube Starter
Fluorescent Tube Locking Tab (tab consists of two pieces) Starter Socket
Upper and Lower Attraction Glass Retainer Steel Tube Bracket Attraction Glass with Graphics Upper and Lower Attraction Glass Retainer Speaker Grille
6 x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker #10 x %-lnch Pan Head Machine Screw 2-Pin Fluorescent Tube Holder Grounding Clip (not shown)
*148001-001
6 x 9-Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin door, behind speaker grille part no. 039144-01
Was this article helpful?
Post a comment