Schematic Diagrams

This chapter contains the schematic diagrams for your Rampart game PCB. The game PCB assembly drawing is illustrated in Chapter 4, Parts Illustrations. -PMIXO - PCMRES TH- *2 iS-TMIXl H-TMIXO YRMRES D8-JJ-GNO-ff- TBMRES-lfc re - r-PCMfll7 -H-PCMR16 - -PCMfll5 -H-PCMR14 - -PCMR13 - 2-PCMftl2 - PCMflll PCMfllO - i-PCMR9 -II-PCMFI8 -ff-PCMR 7 PCMFIfe - -PCMR5 -If- PCMR4 - i-PCMR3 -22- PCMR2 PCMfll -iS-PCMRO PCMR7 I-PCMR6 f PCMR5 it PCMR4 PCMR3-T - PCM07 PCM06 PCMD5 PCM04 PCM03 PCH02 PCMD1 PCMDO...

Joystick Controls

Routine maintenance of the joystick controls consists mainly of inspecting the roller shafts for excessive wear and periodically lubricating the bearings. Maintain the joystick by inspecting the pivot ball, actuator half-ball, and the shaft and by lubricating the joystick with lithium grease. 1. Turn off the power to the game. 2. Open the control panel and disconnect the harness connector 3. Remove the joystick from the control panel. Use a 3 8-inch wrench to remove the nuts and washers that...

Assembling the Control Panel

To assemble the control panel, you need the control panel hole-cutting template, which is printed on page 1-11. Cut out the template sheet from the manual. You will also need the following parts from the kit Clear cover for the control panel Four red and four blue button assemblies Eight control-panel button labels (on a sheet) Eight 10-24 x - -long black carriage bolts, flat washers, and nut washer assemblies for the joysticks Four 10 x long black carriage bolts, flat washers, and nut washer...

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-5. 1 COIN 1 CREDIT BONUS F OR QUANTITY BUY-IN 1 COIN COUNTS AS 1 COIN LEFT MECH VALUE PRESSING RED ROTATE RESTORES ORIGINALSETTING PRESS RED PLACE BUTTON TO SAVE THIS SETTING AND EXIT PRESS RED ROTATE BUTTON TO HEAR SOUND PRESS RED PLACE BUTTON TO RETURN TO MENU Use the joystick to select the sound and press the red ROTATE button to listen to it. Pressing the red PLACE...

Installing the Bezel Decals Labels and Attraction Assembly

The kit parts are shown assembled in a cabinet in Figure 1-1. Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required. Installing the Product ID and FCC Label Place the product ID label part no. 038158-01 and FCC compliance label part no. 039450-01 on the back of the cabinet. Find the side panel decals in the kit. Wet the left and right side...

Connecting the Jamma Harness

1. if your game cabinet does not already have a JAMMA harness, install the JAMMA harness in the cabinet. 2. Install the split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit. You must install the split beads included in the kit on the JAMMA harness to meet FCC requirements. 3. Using Table 1-2 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt...

Tools Required

Drill with a 1 2-inch and 5 l6-inch drill bits Socket wrench set and ratchet Color RGB monitor ' Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency 15.750 KHz Vertical frequency 60 Hz Video input IV to 3V peak-to-peak positive polarity 5 VDC 0.25V U 3.0 amps ' 12 VDC 1.0 amp -5 VDC 1.0 amp optional Insulated wire connectors if you are installing a new JAMMA harness 6 x l 2-Long, Type AB, Pan-Head, Snap-Action Switches 8 ji 10-24 x...